Star Light Canvas

As if you need to be reminded of the star you are, who could resist making a bright starry statement like this? A really simple project, with just a couple of halogen lighting chains, a canvas and emulsion paint my glittery star project will brighten up any room.

You will need-

Emulsion paint

2x Halogen Lighting chain

Paint brush

Paper

Masking tape

Electrical screw driver

Bradawl

1.Paint the canvas with pink matt emulsion paint

2. Draw a large star on a piece of paper then cut out, stick to the reverse of the canvas with a line of masking tape along each straight edge.

3. Work out where you want to have the lights, I had about three along each straight edge and one on each point end.

4. Start making the holes to push the lights through. With one hand supporting the front of the canvas press the bradawl through the masking tape on the reverse and make a pilot hole, next enlarge the hole with the screwdriver, don’t make it too large the light is held in by it. Press the light from the back through the hole to lodge just around the collar of the fitting. Continue round the star with the lights.

5. Hang the canvas up using Command hooks. Do not leave lights on when unattended.

Tip

Before putting the lights into the canvas decide where you want the cables to come out, mine was at the lower edge. I worked out the middle of the total number of light positions on the canvas, this was where I inserted the light at the end of the light chain.

If you like this post check out my post on making your own Christmas decorations 

Turn an old ladder into a contemporary Christmas tree

I made this picture perfect tree out of an old ladder with near-on zero prep, using a coat of chalk paint to cover ancient paint drips and to create a matte finish.

You will need-

• Planed timber

• Saw

• Spirit level

• Pencil

• Drill

• Screws

• Crown Cloudburst matt emulsion paint, £11.99 for 2.5l, Maxwells DIY

• Polyvine Chalk Paint Maker, £11.36, Amazon

• Paintbrush

1. Put up the ladder and decide how steep you want the sides of the tree to be; you might have to remove the retaining cord. Mine was quite broad as I wanted to max out on the display area.

2. To make the back leg shelf supports, cut batten from 2.5cm x 5cm planed timber. With the spirit level balanced on the front step, extend the level line and mark where to locate the support batten on the back legs with pencil. Screw the battens in place.

3. These shelves projected 25cm beyond the edge of the step to give extra display space, but you could make yours shorter if you’d like. Decide on the length, then cut each shelf from planed wood. Screw in place on the front steps and back batten.

4. To make the chalk paint, mix 400ml Crown Cloudburst Matt Emulsion with 200ml Polyvine Chalk Paint Maker. Then, with a crosshatch strokes, paint the ladder Christmas tree and let dry before decorating.

If you like this post check out my funky feather wreath post

Make your own Funky Feather Christmas Wreath

Who wouldn’t want this incredibly chic colourful feather wreath to bring bright carnival colour to your room? I show you how to make this unique wreath with the minimum of effort.

You will need:

Turkey Quills in assorted colours

Polystyrene wreath form

Glue gun

Fishing line

Command Hook

Satay stick

The secret to the wreath is to put the feathers in at an angle so they completely cover the white polystyrene form. Starting pressing in feathers on the outside edge, first, make a pilot hole in the edge of the wreath with a satay stick, press the feather into the hole, then squeeze on a blob of glue to hold. Add the feathers in staggered layers, about 3cm from the next one. Work from the outside to the inside edge moving, around the wreath with each new layer.

When finished decide which is the top of the wreath and tie around a loop of fishing nylon to invisible suspend the wreath from a removable Command hook.

I used:

Specialist Crafts: 3 packs Turkey Quills in assorted colours £6.17

Specialist Crafts: Polystyrene ring approx £1

If you like this check out my post on how to decoupage you own hand plates