Star Light Canvas

As if you need to be reminded of the star you are, who could resist making a bright starry statement like this? A really simple project, with just a couple of halogen lighting chains, a canvas and emulsion paint my glittery star project will brighten up any room.

You will need-

Emulsion paint

2x Halogen Lighting chain

Paint brush

Paper

Masking tape

Electrical screw driver

Bradawl

1.Paint the canvas with pink matt emulsion paint

2. Draw a large star on a piece of paper then cut out, stick to the reverse of the canvas with a line of masking tape along each straight edge.

3. Work out where you want to have the lights, I had about three along each straight edge and one on each point end.

4. Start making the holes to push the lights through. With one hand supporting the front of the canvas press the bradawl through the masking tape on the reverse and make a pilot hole, next enlarge the hole with the screwdriver, don’t make it too large the light is held in by it. Press the light from the back through the hole to lodge just around the collar of the fitting. Continue round the star with the lights.

5. Hang the canvas up using Command hooks. Do not leave lights on when unattended.

Tip

Before putting the lights into the canvas decide where you want the cables to come out, mine was at the lower edge. I worked out the middle of the total number of light positions on the canvas, this was where I inserted the light at the end of the light chain.

If you like this post check out my post on making your own Christmas decorations 

Turn an old ladder into a contemporary Christmas tree

I made this picture perfect tree out of an old ladder with near-on zero prep, using a coat of chalk paint to cover ancient paint drips and to create a matte finish.

You will need-

• Planed timber

• Saw

• Spirit level

• Pencil

• Drill

• Screws

• Crown Cloudburst matt emulsion paint, £11.99 for 2.5l, Maxwells DIY

• Polyvine Chalk Paint Maker, £11.36, Amazon

• Paintbrush

1. Put up the ladder and decide how steep you want the sides of the tree to be; you might have to remove the retaining cord. Mine was quite broad as I wanted to max out on the display area.

2. To make the back leg shelf supports, cut batten from 2.5cm x 5cm planed timber. With the spirit level balanced on the front step, extend the level line and mark where to locate the support batten on the back legs with pencil. Screw the battens in place.

3. These shelves projected 25cm beyond the edge of the step to give extra display space, but you could make yours shorter if you’d like. Decide on the length, then cut each shelf from planed wood. Screw in place on the front steps and back batten.

4. To make the chalk paint, mix 400ml Crown Cloudburst Matt Emulsion with 200ml Polyvine Chalk Paint Maker. Then, with a crosshatch strokes, paint the ladder Christmas tree and let dry before decorating.

If you like this post check out my funky feather wreath post

Create your own handmade Christmas decorations

This nifty little project making Christmas decorations, is one for people who have pets using old pet food containers. We are talking about those lightweight aluminium ones with a lip round them.

You will need:

Clean pet food containers

Patterned paper

Ribbon

Wooden picnic spoons

PVA glue

Paintbrush

Acrylic paint

Thin card

Clear sticky tape

Double sided tape

Acrylic paint

Felt tip pens pencil

Scissors

Instructions:

First cover the inside of the container with the paper face down. Draw around the edge with a pencil. Take a pencil and extend the sideline of the square.

2. Cut out the paper cross shape. Fold the side arms in to crease the paper. Paint the reverse of the paper with a layer of PVA glue, put the paper into the tray, press the two shorter sides onto the tray, then press out the long sides onto the sides. Along the top edge of the tray cut deep nicks in the paper and wrap the paper over the edge to stick in place.

3. To cover the outside of the tray, take a contrast printed paper. Paper face down draw around the base of the tray, cut out square shape. Measure around the outside of the tray, add 1cm for overlap. Cut a strip of paper the measured length and 3cm wide. Paint with PVA glue then wrap around the tray cutting long nicks in the paper to ease around the curved corners, press the loose strips into place on the base, then glue the square of paper over to cover. Poor glitter onto a plate, paint the front edge of the tray with PVA and dip in glitter.

4. To make the portraits, if you like use scissors to trim the top of the spoon into a hairstyle, then paint the spoons with a base coat of white acrylic paint. While they are drying make the shoulders for the portraits. Cut a strip of thin card slightly narrower than the opening of the tray and about 2cm high, fold in half along the length then glue on printed paper.

5. Use acrylic paint to mix a variety of skin tone colours, paint the spoons. Leave to dry then use felt pens to draw on details. Use sticky tape to attach the portrait onto the shoulders. To keep the portrait in position cut a narrow support strut from thin card about 4cm long, fold in both ends by 1cm, then tape one to the reverse of a portrait. Stick the shoulders to the bottom edge of the tray with double sided tape and tape the end of the support strut to the back of the tray. With the point of the scissors make a hole through the top edge of the tray. Cut a length of ribbon and pass one end through the hole and tape in place.

If you like this check out my post on making a star light canvas